**Direct to lung**
The Aspire Cleito Tank consists of 5 parts; widebore Delrin Drip Tip, Metal top cap, Cleito Coil, Pyres Glass tube and a metal base. Easy to take apart and reassemble for cleaning. The tank holds 3.5ml of e-liquid and is 22mm in diameter. Sitting at the very top is the Delrin Drip tip (510 connection) to help dissipate the heat. The elongated tank (60mm height) is crafted using stainless steel and pyrex glass. The Cleito Tank is top-fill, accessible by unscrewing the metal top cap. The top cap and base are sealed with grommets to prevent leaks. 3 airflow slots can be found at the base of the tank which you can open and close depending on your preference.
The Cleito tanks features a revolutionary atomizer design that eliminates all choke points from the coil all the way to the drip tip. This is so the airflow is unimpeded every puff you take. Aspire has replaced the static chimney inside the tank with a full-length coil head that runs the full length of the tank from top to bottom. 2 Kanthal style Clapton coils (organic cotton wicks) are included in this kit with a resistance of 0.2ohm and 0.4ohm (recommended wattage below). To replace coils simply unscrew the base of the tank, remove old coil and screw in the new one, just make sure that you drain out all remaining e-liquid within the tank beforehand!
|0.2ohm||Best between 55-70w|
|0.4ohm||Best between 40-60w|
To use: Priming your new coil is the first task for any new coil/tank and this is no exception. Priming helps to protect your coil and yourself from dry hits or a burnt horrible taste. Unscrew the top lid and remove the glass. Unscrew the base of the tank from the glass to expose the coil within (use the included Cleito Cuff if difficult to unscrew). The coil will now be exposed, and you need not unscrew the coil from the base to prime. You now need to saturate the cotton within the coil with a little e juice (few drops). Take care with priming as these coils are rather tall and it is recommended that you get inside the coil tube and wet the exposed cotton internally. Spin the coil around till you see the cotton getting wet. This ensures proper saturation.
Reassemble your tank and screw back onto your device (at this point it is good practice to check all sealing O rings to ensure no leakage!). Unscrew the top of the tank and fill with e-juice just to ensure complete saturation (don’t overfill though!). Place your device to the side for a short while (5-10 minutes) to allow all the e -juice to make its way through. Now time for the primer puffs, without touching the firing button take a few sharp short pulls from the tank. You may see air bubbles rising to the top of the tank. Your new coil is now ready for use.
Contains: Aspire 3.5ml Cleito sub-ohm Tank,Pre-Installed Cleito Coil -0.4ohm (40-60w), Cleito Replacement Coil – 0.2ohm (55-70w), Spare glass, Cleito Cuffs
Cleito Tank Features:
- Revolutionary full-length vertical coil design
- No choke points from coil to drip tip
- Intense flavours
- Rapid vapor delivery
- 304 stainless steel hardware
- Food-grade Delrin drip tip
- 25.5mm cross section airflow
- Clapton coil build
- Pre-installed 0.4-ohm coil (40w to 60w)
- 0.2-ohm spare in box (55w to 70w)
- Organic cotton wicks
- Pyrex glass tube
- Top-fill tank system
- 3.5ml tank capacity
- 9mm by 2mm adjustable bottom airflow
- Gold-plated contact pin
- 510 threaded
Tank dimensions: 58mm x 22mm diameter