Smok TFV8 The Big Baby Beast 5ml sub ohm Tank

$45.00

×
SKU: N/A Categories: , , , , , Tag:

Description

**Direct to lung tank

Smok’s famous TFV8 sub ohm tank series is back at it again with top level performance and innovative designs to make it one of the most sought-after sub ohm tanks in the market. The TFV8 Big Baby Beast is the enlarged version of the Baby Beast and a more petite version of the Cloud Beast, with a 5ml holding capacity. Other features include precision airflow, signature hinged top-fill system, a large drip tip and the new TFV8 Baby coil structure.

Featuring large dual cyclops adjustable airflow, this tank allows you to finely tune the air until you find that sweet spot. The diameter of the centre chimney has also been enlarged to allow more air to travel through the tank for the least amount of air restriction and the drip tip has been optimised to give you powerful draw effects. In a nutshell, this tank will allow you to savour the flavour of your e liquid whilst leaving a plume of clouds in your wake.

A major bonus of this tank (and of the Baby Beast) is the vast array of coils at your disposal. All coils within the TFV8 Baby Family can be used as well as all coils within the Vaporesso GT Core range. It doesn’t end there as these are many other coils/brands that can also be interchangeable (Eleaf HW and Squid Industries Peacemaker coils – just to name 2).

The following coils/Hyper engines are included with the Big Baby Beast

V8 Baby X4 0.15Ω – Quadruple 30-70W (Best at 45-60W) *Preinstalled
V8 Baby T6 0.2Ω – Sextuple 40-130W (Best at 70-90W)
V8 Baby RBA 0.35Ω – Dual 30-60W (Best 50W)

To use: If using a new coil for the first time be sure to prime it first (very important!), this starts the wicking process and helps to prevent dry hits. To prime simply unscrew the drip tip, top cap and glass tube (all in one piece) off the base to expose the installed coil. You may need to remove an old coil and rethread a new one (not too tight as you will need to remove it at some point!). Drip a small amount of your e juice onto the exposed cotton around the perimeter as well as the interior of the new coil.

Reassemble your tank and thread onto your mod/battery to fill. To fill the tank hold with one hand and use the other hand to press the button on the top cap and then swivel the lid counterclockwise. You can now add your e liquid via a dropper into the slot (be careful to not drip any into the centre airflow tube). Swivel back the top cap and allow the unit to sit for a few more minutes. Now time for the primer puffs – without touching the firing button take a few sharp short pulls from the tank. You may see air bubbles rising to the top of the tank. Lastly it is quite important (for your safety) that you ensure that you select the right wattage on your device (mod box) for the coil being used. Each coil has its wattage range imprinted on the side (you may need a magnifying glass though!). You are now ready to vape!

To build the RBA: Make sure your hands are clean to start. Take the included RBA deck apart. Install and position the pre-wrapped coil. Place the coil between the posts and wrap the ends around the screws and tighten. Once all is in place make sure the coil is fixed in the centre, is lined up with the airhole and does not touch the base. Cut the excess ends of wire off. Cut a strip of cotton (not too much or too little). Insert the cotton into the middle of the coil. Cut the cotton at an angle making sure it is not too short or too long. Wet the coil with your e-liquid and adjust the cotton. Make sure to check coils for resistance before they are fired on a device and re-check periodically to make sure the resistance stays the same.

To Clean: Every once in a while, I recommend disassembling your tank, so you are able to give the various components (not coils though) a good clean. Isopropyl Alcohol, cotton buds (Higher Standards Pipe Stix work well as the cotton does not unravel) and water should get your glass and top cap and drip tip back to almost new. Leave to air dry for around 10 minutes as electricity and water don’t mix well together!

Contains – x1 TFV8 Big Baby Tank, V8 Baby – X4: 0.15Ω Quadruple coils (pre-installed), x1 V8 Baby – T6: 0.2Ω Sextuple coil, x1 V8 Baby RBA, x1 1 replacement glass tube for RBA, x1 1 replacement glass tube, x1  510 drip tip adapter, spare parts and instruction manual.

Specifications

  • Capacity: 5ml
  • Height: 56mm
  • Diameter: 24.5mm
  • Weight: 60g
  • Material: Stainless Steel
  • Thread: 510

Additional information

color

Black, Carbon Fibre

Reviews

There are no reviews yet.

Be the first to review “Smok TFV8 The Big Baby Beast 5ml sub ohm Tank”

Your email address will not be published. Required fields are marked *

+ 34 = 44